- #Connect 2009 yamaha f 115txr to nmea 2000 network how to
- #Connect 2009 yamaha f 115txr to nmea 2000 network manual
- #Connect 2009 yamaha f 115txr to nmea 2000 network full
- #Connect 2009 yamaha f 115txr to nmea 2000 network pro
#Connect 2009 yamaha f 115txr to nmea 2000 network manual
Manual source select (tanks)Settings Network Sources>Advanced>Fuel Tank.Drill down in to each tank sender and select the desired source. Run the network auto source selection Settings>Network>Sources>Auto-source Select. Set the fl uid type to Fuel and the capacity >OK
#Connect 2009 yamaha f 115txr to nmea 2000 network how to
Outline Set number of tanks Confi gure Fluid levels sensors for Fluid Type, Instance andĬapacity Set data Sources Confi gure Yamaha tank settingsThe following is how to setup two fuel tanks fi tted NMEA 2000 Fluid level sensorsSelect HOME (PAGES)Select FUEL >VESSEL SETUPSet number of Fuel tanksĬonfi gure Fluid level SensorsSelect HOME(PAGES) > Settings > Network > Device List.Select a Fluid level Sensor from the device listĪssign a tanks instance number then Yes to change Note: If you have four engines and two side-by-side displays you can select the Quad P to display the two port side engines on one screen and Quad S to display the starboard pair on the other screen.Īdvanced: Setting up NMEA 2000 Tank SensorsSetup of NMEA 2000 Fluid level sensors is required before the Yamaha page can display tank levels.Below is how to setup Navico Fluid level sensors (000-11518-001) or EP-65 It can be accessed from the side menu at any time This will need to be completed on each MFD. Power on the MFDIf a compatible gateway is detected the Yamaha features are enabled
![connect 2009 yamaha f 115txr to nmea 2000 network connect 2009 yamaha f 115txr to nmea 2000 network](https://www.yachtbits.com/image/cache/catalog/prod/actisense/3852-1_1-800x800.jpg)
![connect 2009 yamaha f 115txr to nmea 2000 network connect 2009 yamaha f 115txr to nmea 2000 network](https://panbo.com/assets_c/2013/10/Actisense_EMU-1_install_cPanbo-thumb-465xauto-8031.jpg)
#Connect 2009 yamaha f 115txr to nmea 2000 network pro
Yamaha Command Link, Command Link Pro with CL7 Gauge HDS GEN3, HDS CarbonWith software version 58.xx.xxx or greaterĭ Network Power IsolatorNavico Part 000-12259-001 Micro-C network power isolator. Do not use Gateway 6YG-8A2D0-00-00 in this confi gurationB Compatible Navico Multifunction display SIMRAD NSSevo2, NSOevo2, NSSevo3, GO7, GO9, GO12Lowrance
![connect 2009 yamaha f 115txr to nmea 2000 network connect 2009 yamaha f 115txr to nmea 2000 network](https://www.suzuki-china.com/img/marine/marine-outboard/23.jpg)
![connect 2009 yamaha f 115txr to nmea 2000 network connect 2009 yamaha f 115txr to nmea 2000 network](https://i.ytimg.com/vi/3mnEEmRraqk/maxresdefault.jpg)
NOS60 and above support a gateway only confi gurationĬ NMEA 2000 drop cable (max length 6 m 20 ft)000-0119-88 - N2KEXT-2RD - 0.61 m (2-ft) NMEA 2000000-0127-53 - N2KEXT-6RD - 1.82 m (6-ft) NMEA 2000000-0119-86 - N2KEXT-15RD - 4.55 m (15-ft) NMEA 2000(N2K-T-RD T - Micro-C T-connector also required)ĭ Compatible Navico Multifunction displays SIMRAD NSS evo2, NSO evo2, NSS evo3, GO7, GO9, GO12LowranceHDS GEN3, HDS CarbonWith software version 58.xx.xxx or greaterĪ Yamaha CL7 Gauge: This has built in gateway that will unlock the Yamaha featuresNote.
#Connect 2009 yamaha f 115txr to nmea 2000 network full
Note: MFD Application software version less than NOS60.1.xx require the a gateway and the 6Y9 gauge for full functionality. Yamaha Command Link Pro NetworkNavico NMEA 2000 NetworkĪ Yamaha 6Y9 gauge: This confi guration requires a Gateway (6YG-8A2D0-00-00 ) to unlock Yamaha features in the MFD softwareB Yamaha NMEA 2000 Gateway part # 6YG-8A2D0-00-00 & Pigtail wire part #6Y8-8: PARTS REQUIRED to enable Yamaha features of the Navico MFD. POWER DEVICE DEVICE DEVICEBUS BUS POWER DEVICE DEVICE DEVICEBUS BUSĤ Engine max(See list of compatible engines)